Total Protection Films
Home security window film: a masked intruder raising a crowbar at the window of an upscale home with a chandelier inside

Home Window Tinting

Security Window Film for Homes

Security window film for homes is a thick, clear polyester film that bonds to your glass and helps hold it together when it breaks. It can slow entry through a slider, pocket door or entry sidelight and keeps shards in place near pools, without changing how the house looks. It starts from $9.50 per square foot.

  • From $9.50 per sq ft installed
  • Most homes finished in a day
  • XPEL Limited Lifetime residential warranty
Authorized installerArmorcoat authorized installer badgeSafetyShield G2 by Madico qualified dealer logo

Overview

What security window film does when glass breaks

A home designed around glass has more of it at ground level than most: walls of sliders, pocket doors that open the great room to the patio, tall entry glass and view windows that face a quiet side of the lot. Ordinary glass, especially the annealed glass in many older Arizona homes, breaks into sharp pieces that fall out of the frame. Security window film changes that. It is a thick, tough polyester laminate with a strong adhesive, and once it bonds to the pane, broken glass tends to stay on the film instead of spilling across the floor.

For the household that means two things. Someone trying to get in through a slider or a window has to keep working at a sheet of cracked but connected glass, which takes time and makes noise. And an accidental break, from a fall against a patio door or a stray ball by the pool, leaves fewer loose shards around bare feet, pets and the furnishings near the glass.

Security film is a deterrent and a safety layer. It does not make glass unbreakable, bulletproof or burglar-proof, and we won’t sell it that way.

Part of our home window tinting services; also available as security window film for commercial buildings.

Where it goes

Where safety window film goes in a home

Break-ins and accidents tend to find the same few openings. These are the places we film most often:

  • Sliders, pocket doors and multi-panel glass walls

    Big panes, usually at the back of the house and out of view from the street. Our article on shatterproof film for sliding glass doors covers this opening in depth.
  • Entry glass, pivot doors and sidelights

    Breaking a small pane to reach a lock is a common approach.
  • Ground-floor windows on a side yard or alley,

    Where nobody is watching.
  • Glass around the pool and patio,

    Where people are barefoot and a break would scatter shards into the water.
  • Casitas and guest wings

    That sit apart from the main house and may be empty for long stretches.
  • Glass near stairs and low windows

    That a child or a large dog could fall against.

Thickness

Choosing a shatter resistant film thickness

Security films are sold by thickness, measured in mil (thousandths of an inch). We install films from 4 to 14 mil. Thicker film is stiffer and holds more glass, but it also costs more, and the right answer depends on the opening.

XPEL publishes strength figures for its Security Clear line on 3 mm glass. Security Clear 4mil is rated at a break strength of 120 lbs per inch and a puncture strength of 70 lbs. Security Clear 8mil doubles that break strength to 240 lbs per inch, with a puncture strength of 141 lbs. Security Clear 14mil is rated at 420 lbs per inch break strength and 230 lbs puncture strength. All three are published at a tensile strength of 30,000 psi.

As an Armorcoat authorized installer, we also install the Solar Gard Armorcoat-Clear range in 4, 7, 8, 10, 11 and 14 mil. Solar Gard publishes these at 86% to 88% visible light on 6 mm clear glass.

Clear window security film you can forget

Owners of architect-designed homes usually want protection that no one can see. Clear security films are built for that. XPEL publishes its Security Clear films at 88% to 89% visible light on 3 mm glass, and the Armorcoat-Clear figures above are similar on Solar Gard’s own test glass. Neither changes the outside of the house in a way your architect, HOA or neighbors would notice, and the view from inside stays as it was.

Clear security film also blocks UV. XPEL publishes 99% UV blocking for Security Clear, and Solar Gard publishes more than 99% for Armorcoat-Clear, which helps protect wood floors, rugs and upholstery behind a wall of sliders.

What clear security film won’t do is cut much heat. If a slider takes hard afternoon sun, look at our solar window film options for that wall as well.

Interior or exterior security film

Most security film goes on the interior face of the glass. For some openings, film on the outside is the better choice, for example when the inside face is hard to reach or the glass type limits interior films. XPEL Exterior Security Clear 7mil is made for exterior application and is published at a break strength of 175 lbs per inch and a puncture strength of 115 lbs on 3 mm glass.

Specs

Security window film specs

XPEL Security Clear

FilmVisible light transmittedTotal solar energy rejectedSHGCUV blockedGlare reduction
Security Clear 4mil (4 mil)89%17%0.8399%0%
Security Clear 8mil (8 mil)89%18%0.8299%1%
Security Clear 14mil (14 mil)88%19%0.8199%2%

Manufacturer-published values measured on 1/8" (3 mm) glass; results on your windows vary by glass type. Sources: spec sheet

Solar Gard Armorcoat-Clear

FilmVisible light transmittedTotal solar energy rejectedSHGCUV blockedGlare reduction
Armorcoat-Clear 4 mil (4 mil)88%21%0.79>99%n/a
Armorcoat-Clear 7 mil (7 mil)88%21%0.79>99%n/a
Armorcoat-Clear 8 mil (8 mil)88%21%0.79>99%n/a

Manufacturer-published values measured on 1/4" (6 mm) clear glass; results on your windows vary by glass type. Sources: spec sheet

Anchoring

Anchoring systems for sliders and doors

Film on its own holds broken glass to itself, but the whole sheet of cracked glass can still push out of the frame. An attachment system ties the filmed glass to the frame so it stays in the opening longer. For sliders and back-of-house doors where entry is the main concern, this is the step that matters most after film thickness.

We are a Madico SafetyShield qualified dealer and offer several ways to do it:

  1. Wet glazing

    A bead of structural silicone bonds the filmed glass to the frame. We use DOWSIL 995, which Dow publishes at 350 psi tensile strength and +/- 50% movement capability. Madico’s SafetyShield Wet Glaze method calls for at least 1/2 inch of contact on both the film and the frame.
  2. Madico SafetyShield FrameGard

    An aluminum extrusion clamps the filmed glass to the frame with screws and tape. Madico reports testing it to hold 500 to 800 pounds per linear foot of attachment.
  3. Madico SafetyShield GullWing

    A profile sized to fit different frames and designed to spread energy across the whole glazed opening.

Madico lists SafetyShield testing to ANSI Z97.1, ASTM F1642, ASTM F3561 and EN 356. Those are Madico’s published results for its system, not a rating of your house. Attachment is priced per project, after we see the frame and the glass.

Security window film installation

Get a free consultation

Before work starts, the crew protects floors, rugs and furnishings near each opening and asks before moving anything. Security film works best when it covers the whole visible pane. We clean the glass thoroughly, cut film tight to the edge of the frame and squeegee it down for a solid bond across the glass. On tempered glass, which already breaks into small pieces, the film’s main job is to hold those pieces together. On annealed glass, it also helps keep large, sharp shards from falling out.

Most homes are finished in a day. A slight haze is normal at first and usually clears in a few days, depending on the weather. Solar Gard’s care guidance is to wait 30 days before cleaning the film, then use mild dish soap and water with a soft cloth.

Cost

What home security film costs

Residential security film starts from $9.50 per square foot. Thicker films cost more than thinner ones, removing old film adds $4.50 per square foot, and upper-floor or lift access adds 15%. Every job starts with a written proposal that lists the film and thickness for each opening, so you can decide which doors and windows to protect first.

XPEL’s Security Clear films (4, 8 and 14 mil) carry a Limited Lifetime residential warranty from XPEL, and its exterior films carry 5 years on the film and 2 years on labor, which requires installation by an authorized dealer. For more on coverage, see our window film warranty page. Homeowners who also want to block the view into a ground-floor room can add privacy window film to the plan. Our full residential lineup is on the home window tinting page, and business owners should see commercial security window film.

Security window film cost per square foot

Installed prices start at $9.50 per square foot. Your written proposal is based on measured glass, film choice and access.

Film gradeInstalled price per sq ft
SecurityFrom $9.50

Prices as of October 2026, from our bid-tool customer rates. Old film removal adds $4.50 per sq ft; upper-floor or lift access adds 15%.

Who installs your safety and security film

We are licensed by the Arizona Registrar of Contractors (ROC #333727) and install across the Phoenix and Tucson metros. Owner Chris Fill has 25 years in the window film business and is a licensed glazing contractor in Arizona, so door glass, tempered panes and frames are familiar ground. Every proposal lists film, thickness and square footage by opening.

Watch a security window film install

  • Security window film install on a sliding glass doorClear 8 mil security film on an Arcadia sliding door, anchored to the frame with DOWSIL 995 structural silicone.In this video Cleaning the glass and installing 8 mil security film Applying DOWSIL 995 structural silicone to anchor the film to the frame Tooling the silicone and pulling the tape The finished attachment edgeWatch on YouTube

Common questions

Security window film questions

Have a question about your glass? Ask us.

Will security film keep a burglar out of my house?

No film makes glass unbreakable or burglar-proof. What it does is hold broken glass together, so getting through takes more time and makes more noise, which can discourage an intruder and give you time to react.

What thickness of security film do I need for a sliding door?

Homeowners usually choose a thicker film for sliders and back-of-house doors than for ordinary windows. We install films from 4 to 14 mil and recommend a thickness after seeing the door and its glass.

Can you see security window film once it is installed?

Barely. XPEL publishes its Security Clear films at 88% to 89% visible light on 3 mm glass, and Solar Gard publishes Armorcoat-Clear at 86% to 88% on 6 mm clear glass, so the windows look much the same as they do now.

Does security film help with glass around a pool?

Yes, that is one of the most common reasons homeowners install it. If filmed glass breaks, the pieces tend to stay on the film instead of falling onto the deck or into the water.

Does clear security film block UV?

Yes. XPEL publishes 99% UV blocking for its Security Clear films on 3 mm glass, and Solar Gard publishes more than 99% for Armorcoat-Clear on 6 mm clear glass.

Can security film be removed later?

Yes, but thick security film is bonded to hold glass, so taking it off is real work. Removing old film adds $4.50 per square foot when we install new film.

Does security film keep heat out?

Not much. Clear security film is built for strength and clarity, not heat rejection. For a slider that takes hard afternoon sun, we can talk through solar film for that opening.

Free consultation

Book a free window tinting consultation

Tell us about your glass and we'll send a written proposal.

(480) 977-6994
  • Arizona: ROC Lic# 333727

By submitting, you agree to receive calls and texts about your request from Total Protection Films. Msg & data rates may apply. Reply STOP to opt out. See our privacy policy.

Licensed, factory-authorized window film installers

  • Arizona: ROC Lic# 333727
  • Solar Gard / Saint-Gobain authorized dealer
  • Armorcoat authorized installer
  • XPEL authorized dealer
  • Madico SafetyShield qualified dealer
  • Full XPEL VISION line installed
  • 25 years of window film experience

Because we're factory-authorized, film is installed to manufacturer spec and carries the manufacturer's warranty.