Total Protection Films
Home decorative window film: a floor-to-ceiling frosted glass panel in a modern bathroom

Home Window Tinting

Decorative Window Film for Homes

Decorative window film for homes is a frosted or textured film that changes how glass looks, adds soft privacy and diffuses light. Homeowners use it on frameless showers, entry glass, wine rooms and cabinet doors. We install it across the Phoenix and Tucson metros, starting from $8.25 per square foot.

  • From $8.25 per sq ft installed
  • Samples on your own glass
  • Most homes finished in a day

Overview

Decorative window film that looks designed, not covered

Decorative window film changes the look of glass without replacing it. It is a thin film, usually frosted or finely textured, that bonds to the pane and gives clear glass an etched or sandblasted appearance. Light still comes through, and the view softens or disappears.

In a well-finished home, decorative film tends to do two jobs. It adds privacy where a shade or curtain would look wrong, such as a frameless shower, a narrow sidelight or a glass wine room wall, and it gives plain glass a deliberate, architectural finish. Because film can come off later, it is a lower-commitment way to try a look than ordering new frosted glass and waiting on a glazier.

Part of our home window tinting services; also available as decorative window film for commercial buildings.

Finishes

Frosted decorative window film finishes

We keep the decorative lineup to a few frosts that look right on residential glass and hold up to daily use.

XPEL Dusted Crystal is the lightest frost. XPEL publishes it at 86% visible light on 3 mm glass, so it softens the view while keeping a room nearly as bright as untreated glass. It suits glass cabinet fronts, interior French doors and places where a hint of texture is the goal rather than full privacy. One caution: XPEL publishes its UV blocking at 35%, far below our solar films, so it is not the film for a sunny window above a rug or a painting. For that glass, UV protection window film keeps the pane close to clear while blocking 99% or more of UV, and White Frost below gives privacy and UV protection together.

XPEL White Frost is denser and whiter. XPEL publishes it at 65% visible light and 99% UV blocking on 3 mm glass. It is our usual choice for bath windows and entry glass, where privacy matters and the floor or furnishings near the glass also need protection from the sun.

Madico Frost Matte gives a classic etched-glass look. Madico publishes it at 67% visible light on 6 mm clear glass. Owners often choose it to sit beside factory-etched glass already in a door or transom.

We bring samples of each so you can judge them on your own glass, in your own light, before anything is ordered.

Where it goes

Decorative privacy film for showers, doors and cabinets

  • Frameless shower enclosures and tub windows

    Film goes on the dry side and gives the glass an etched finish.
  • Entry doors, pivot doors, sidelights and transoms

    A frost keeps daylight in the foyer while stopping the view down the hall.
  • Wine rooms and glass-walled pantries

    A band or a bordered frost can frame the room without hiding it entirely.
  • Glass cabinet fronts and bar cabinetry

    A light frost quiets what sits behind it.
  • Interior glass doors to an office, gym or media room

    Privacy for calls and workouts without losing borrowed light.
  • Large sliders and pocket doors

    A frosted band at eye level makes wide panes easier to see, which helps keep guests, children and dogs from walking into the glass.

Designing frosted bands and borders

Decorative film does not have to cover the whole pane. We trim it by hand on the glass, so it can go on as a band across a door, a frosted lower section on a bath window, or a full frost with a clear margin at the edge. Simple stripes, or a clear border inside each lite of a divided-lite door, can make the glass look as though it was ordered that way.

Tell us what you want to see through and what you want to hide. If your designer or architect has a finish schedule or a drawing, we work from it. Either way, we mark the line on the glass with you before the film goes on, so the band lands where the sightline actually is.

Choosing

Choosing frosted window film for each spot

A short way to narrow it down:

  1. Texture without privacy

    Dusted Crystal. It keeps the most light and works on interior glass that never sees direct sun.
  2. Privacy and sun protection

    White Frost. It is the denser XPEL frost and blocks UV, so it suits exterior windows and entry glass near wood floors.
  3. Match an etched look already in the house

    Frost Matte, held against your existing glass to compare.

In a home with many kinds of glass, one frost used throughout usually looks more considered than a mix of finishes. An entry door and the sidelights beside it should almost always match.

Specs

Decorative window film specs

XPEL

FilmVisible light transmittedTotal solar energy rejectedSHGCUV blockedGlare reduction
Dusted Crystal86%17%0.8335%4%
White Frost65%33%0.6799%28%

Manufacturer-published values measured on 1/8" (3 mm) glass; results on your windows vary by glass type. Sources: spec sheet

Madico

FilmVisible light transmittedTotal solar energy rejectedSHGCUV blockedGlare reduction
Frost Matte67%n/an/an/a25%

Manufacturer-published values measured on 1/4" (6 mm) clear glass; results on your windows vary by glass type. Sources: spec sheet

How decorative film installation goes

Get a free consultation

We start with the layout. A full frost needs no decisions, but bands, borders and partial coverage are measured pane by pane and agreed with you. Divided-lite doors take longer, because each small lite gets its own piece of film trimmed to the muntins.

On install day the crew lays protection over floors and nearby furnishings, cleans the glass, removes any old film or residue, applies the film wet and squeegees it flat. Edges are trimmed so the frost sits evenly inside the frame. A frosted finish can look slightly cloudy or show small pockets while the adhesive cures, and that settles as the water dries. Most homes are finished in a day, and the work area is left as we found it.

Frosted window film or new frosted glass?

Replacing a shower panel or a door lite with factory-frosted glass means ordering glass, waiting for it and having a glazier swap it, sometimes with hardware removed and reset. Film goes on the glass already in place. If your taste changes, or the house is sold, film can come off. When we remove old film before a new install, removal adds $4.50 per square foot.

Film also leaves the glass itself unchanged. Tempered shower glass is still tempered glass with film on its surface.

Care for frosted film, including shower glass

Frosted film cleans like glass: a soft cloth with mild dish soap and water, and no razor blades or abrasive pads. On a shower enclosure, film on the dry side stays clear of soap, hard water and the squeegee. Manufacturer care guidance is to wait 30 days before the first cleaning, which is worth passing on to whoever cleans the house.

Decorative film is about appearance and soft privacy, not heat. If a frosted window also takes strong afternoon sun, our privacy window film page covers darker and reflective options, and solar window film covers heat control for the view glass.

Cost

Decorative film cost, warranty and HOA notes

Privacy frost films start from $8.25 per square foot, and the written proposal lists the film and square footage for every pane. Upper-floor or lift access, such as a tall entry transom, adds 15%, and removing old film or residue adds $4.50 per square foot. XPEL warrants White Frost and Dusted Crystal for 5 years on a home with an authorized dealer install, and our window film warranty page explains what that covers and how a claim is made. Most decorative work is on interior glass the HOA never sees, and a frosted window facing the street looks much like the obscured glass already common in baths.

For more on doors, read our article on glass door tinting in Scottsdale. The full residential lineup is on the home window tinting page, and for lobbies, conference rooms and storefronts see commercial decorative window film.

Decorative window film cost per square foot

Installed prices start at $8.25 per square foot. Your written proposal is based on measured glass, film choice and access.

Film gradeInstalled price per sq ft
Privacy frostFrom $8.25

Prices as of October 2026, from our bid-tool customer rates. Old film removal adds $4.50 per sq ft; upper-floor or lift access adds 15%.

Common questions

Decorative window film questions

Have a question about your glass? Ask us.

Can decorative film go on a shower door?

Yes. We apply it to the dry side of the glass, which keeps it away from water, soap and squeegees and gives the enclosure an etched look.

How much light does frosted window film let in?

It depends on the frost. XPEL publishes Dusted Crystal at 86% visible light and White Frost at 65% on 3 mm glass, and Madico publishes Frost Matte at 67% on 6 mm clear glass.

Is decorative window film permanent?

It bonds with a permanent adhesive and is meant to stay, but it can be taken off later without replacing the glass. That makes it a sensible choice if you might want a different look down the road.

Can you frost only part of a window or door?

Yes. We cut film on the glass, so it can be a band, a lower section or a full frost with a clear border.

Does decorative film block UV?

Some finishes do and some don't. XPEL publishes White Frost at 99% UV blocking, while its lighter Dusted Crystal is published at 35%, so we pick the frost based on whether sun and fading matter at that window.

Can decorative film match my existing frosted glass?

Often it can come close. We bring samples of each frost so you can hold them against your existing glass and pick the nearest match before anything is ordered.

Will decorative film help people see a sliding glass door?

Yes. A frosted band at eye level makes a large clear pane easier to notice, which helps keep kids, guests and pets from walking into it.

Can my designer or architect specify the frost and layout?

Yes. We are glad to work from a designer's drawing or finish schedule, bring samples for their approval, and mark the layout on the glass with them before the film goes on.

Free consultation

Book a free window tinting consultation

Tell us about your glass and we'll send a written proposal.

(480) 977-6994
  • Arizona: ROC Lic# 333727

By submitting, you agree to receive calls and texts about your request from Total Protection Films. Msg & data rates may apply. Reply STOP to opt out. See our privacy policy.

Licensed, factory-authorized window film installers

  • Arizona: ROC Lic# 333727
  • Solar Gard / Saint-Gobain authorized dealer
  • Armorcoat authorized installer
  • XPEL authorized dealer
  • Madico SafetyShield qualified dealer
  • Full XPEL VISION line installed
  • 25 years of window film experience

Because we're factory-authorized, film is installed to manufacturer spec and carries the manufacturer's warranty.