Total Protection Films
Commercial security window film being installed in an elementary school classroom: a roll of clear film on an applicator rig in front of steel-frame windows

Commercial Window Tinting

Commercial Security Window Film

Commercial security window film is a thick, clear polyester laminate bonded to storefront, office and door glass so that broken glass stays together, slowing forced entry and reducing flying shards. We install Solar Gard Armorcoat and XPEL Security Clear films from 4 to 14 mil across Arizona, from $9.50 per square foot.

  • From $9.50 per sq ft installed
  • Clear film from 4 to 14 mil
  • Before-opening or after-close installs
  • 10-year XPEL commercial warranty
Authorized installerArmorcoat authorized installer badgeSafetyShield G2 by Madico qualified dealer logo

Overview

What commercial security window film does when glass is hit

Most smash-and-grab losses start the same way: a rock, a hammer or a vehicle part through a storefront or door, then a few seconds inside. Ordinary glass gives way at the first hard strike and falls out of the frame. Security film changes that sequence. Bonded to the inside of the pane, it holds the broken pieces together as a sheet, so the opening does not clear on the first blow.

That is the honest promise of security film. It does not make glass unbreakable, bulletproof or burglar-proof. It adds time and effort, keeps broken glass from spraying across a sales floor or reception area, and can make a target less attractive than the business next door.

For the wider set of films we install on commercial buildings, see our commercial window tinting hub.

Who it's for

Smash-and-grab film for storefronts, offices and clinics

  • Retail storefronts

    Display windows and the glass around entry doors are the usual targets after hours.
  • Glass entry doors and sidelites

    Often the first glass someone tries, and the glass most likely to be hit by accident in a busy lobby.
  • Ground-floor offices

    Street-level offices with laptops and equipment in view through the window.
  • Medical and dental suites

    Ground-floor suites with medication or equipment on site, and waiting rooms where broken glass would be a hazard.
  • Schools and front offices

    Reception glass and vestibules, with installs scheduled over breaks.
  • Restaurants and bars

    Large front glass that sits dark and unattended overnight.

We also install it on interior glass, such as glass partitions in office suites, where the goal is limiting flying glass rather than stopping entry.

High-risk sites

Government buildings, houses of worship and other high-risk sites

Some buildings face threats that go beyond an overnight smash and grab. City and county offices, courts and other public buildings deal with angry visitors and protests. Churches, synagogues, mosques and temples, along with cultural and community centers, have been targets of vandalism and hate crimes, often through the glass at the front of the building. For these sites the goal is time: glass that holds together for longer after the first blows gives staff and worshippers time to lock down, move to a safe room and call for help, and keeps broken glass from spraying into a sanctuary, lobby or classroom.

What we recommend for high-risk sites:

  1. Thicker film with an attachment system

    Clear security film at the heavier end of the 4 to 14 mil range, anchored to the frame with structural silicone or a Madico SafetyShield system (see anchoring and attachment systems below), so the filmed glass stays in the opening instead of falling out as one sheet.
  2. Entry doors, sidelites and vestibules first

    These are where most forced entry starts. We survey every opening and rank the glass by exposure so a limited budget goes where it matters.
  3. Lower glass and street-facing windows

    Windows a rock or a bat can reach from the sidewalk or parking lot.
  4. Privacy where it helps

    At reception desks and guard posts, one-way film or frosted film can keep people inside from being watched while they keep their view out.

Nonprofits at high risk of attack, including houses of worship, can apply for physical security improvements through FEMA’s Nonprofit Security Grant Program, which in Arizona is administered by the Arizona Department of Homeland Security. Whether film qualifies depends on the program’s rules and your vulnerability assessment, so check before you budget on it; we provide the written proposal, product data and attachment details that an application usually needs. We have done grant-funded security film before, at an elementary school in Skull Valley.

We keep security work confidential. We do not publish a client’s name, address or photos of a security installation without the owner’s permission.

Thickness

8 mil security window film and other thicknesses

Security film is sold by thickness in mil (thousandths of an inch). Thicker film resists tearing better but costs more and needs glass and frames that suit it.

XPEL publishes break strength for its Security Clear line, all on 3 mm glass:

  1. Security Clear 4mil

    120 lbs/in break strength and 70 lbs puncture strength.
  2. Security Clear 8mil

    240 lbs/in break strength and 141 lbs puncture strength.
  3. Security Clear 14mil

    420 lbs/in break strength and 230 lbs puncture strength.

Solar Gard Armorcoat-Clear comes in 4, 7, 8, 10, 11 and 14 mil, tested on 6 mm clear glass. Because the test glass differs, we do not set Armorcoat and XPEL figures side by side as if they were measured the same way. We use each manufacturer’s data on its own terms and choose the film that suits your glass.

As a starting point, thinner films suit interior partitions and general safety glazing, mid-range films suit most storefront and door glass, and the heaviest films are for high-risk ground-floor glass where the owner wants the most resistance film can offer.

Clear shatter resistant window film for storefronts

A storefront that looks boarded up costs sales. Clear security film keeps the glass looking like glass. Solar Gard publishes Armorcoat-Clear 4 mil at 88% visible light transmission on 6 mm clear glass. XPEL publishes Security Clear 4mil at 89% on 3 mm glass. Both also block UV, with Armorcoat-Clear published at more than 99% and XPEL Security Clear at 99%, which helps protect merchandise in the window.

Security films are not heat-control films. If the same glass also takes hard afternoon sun, we can discuss a solar window film for other elevations, or a combined approach on the storefront.

Exterior glass protection film

Some glass cannot be filmed from the inside, such as glass behind fixed displays or casework. XPEL Exterior Security Clear 7mil is designed for the outside face of the glass and is published at 175 lbs/in break strength and 88% visible light transmission on 3 mm glass.

Specs

Commercial security window film specs

XPEL Security Clear

FilmVisible light transmittedTotal solar energy rejectedSHGCUV blockedGlare reduction
Security Clear 4mil (4 mil)89%17%0.8399%0%
Security Clear 8mil (8 mil)89%18%0.8299%1%
Security Clear 14mil (14 mil)88%19%0.8199%2%

Manufacturer-published values measured on 1/8" (3 mm) glass; results on your windows vary by glass type. Sources: spec sheet

Solar Gard Armorcoat-Clear

FilmVisible light transmittedTotal solar energy rejectedSHGCUV blockedGlare reduction
Armorcoat-Clear 4 mil (4 mil)88%21%0.79>99%n/a
Armorcoat-Clear 7 mil (7 mil)88%21%0.79>99%n/a
Armorcoat-Clear 8 mil (8 mil)88%21%0.79>99%n/a

Manufacturer-published values measured on 1/4" (6 mm) clear glass; results on your windows vary by glass type. Sources: spec sheet

Anchoring

Anchoring and attachment systems

Film on its own holds glass together, but the whole sheet can still be pushed out of the frame. An attachment system ties the filmed glass to the framing so the opening stays closed longer under a sustained attack, a blast or a storm. Madico does not recommend a simple daylight installation of safety film, and recommends an anchoring restraint system for glass with a risk of spontaneous breakage.

We are a Madico SafetyShield qualified dealer. The options we specify:

  1. Wet glazing with structural silicone

    We bond the filmed glass to the frame with DOWSIL 995, a structural silicone that Dow publishes at 350 psi tensile strength with +/- 50% movement capability. Madico’s SafetyShield Wet Glaze method requires at least 1/2 inch of contact on both film and frame.
  2. Madico SafetyShield FrameGard

    An aluminum extrusion, screws and tape clamp the filmed glass to the frame. Madico reports FrameGard tested to hold 500 to 800 pounds per linear foot of attachment.
  3. Madico SafetyShield GullWing

    A profile sized for different frames and designed to absorb and spread energy across the full glazed opening.
  4. Madico SafetyShield LifeLine

    Energy-absorbing cords that restrain shattered glass, made for industrial and manufacturing settings. Madico reports the cords tested to withstand blasts up to 10 psi.

Madico lists SafetyShield testing to ANSI Z97.1 (safety glazing), ASTM F1642 (blast mitigation), ASTM F3561 (forced entry after simulated active shooter) and EN 356 (manual attack). Those results are Madico’s, published for its system; they are not a certification we hold or a rating of a specific building. Attachment systems are priced per project once we have surveyed the frames.

Case study

A school we secured in Skull Valley

In July 2023 we installed clear 8 mil security film at an elementary school in Skull Valley, near Prescott. The brick building dates to the early 1950s, and many of its steel-frame windows are close to 75 years old; the school paid for the work with a construction grant for security upgrades. In the classrooms, the filmed glass is held to the frames with Madico SafetyShield GullWing. In the front office, we wet glazed the film to the frames with DOWSIL 995 structural silicone. The job covered about 1,100 square feet of film and attachments and took two installers and a helper four days. Window Film Magazine wrote about the project: Arizona Elementary School Upgrades Security With Film (July 2023).

See all window film projects →
  • Security window film being installed in an elementary school classroom with steel-frame windows

    Security window film in Skull Valley, AZ

    Elementary school security film

    Skull Valley, AZ · Security Window Film · 1,100 sq ft ·

    Clear 8 mil security film on the steel-frame windows of an early 1950s brick school, anchored with Madico SafetyShield GullWing in the classrooms and DOWSIL 995 wet glazing in the office. Two installers and a helper, four days, funded by a school security grant.

    Featured in Window Film Magazine: Arizona Elementary School Upgrades Security With Film

What we check before recommending a film

Security film performs only as well as the glass and frame it is attached to, so the survey matters as much as the product.

  1. Glass type

    Annealed, tempered, laminated and insulated glass each break differently. We note what is in every opening and match the film to it.
  2. Frame and glazing

    Old gaskets, loose stops and worn storefront framing can let a filmed pane push out as one sheet. We flag frames that need attention before anchoring makes sense.
  3. Glass warranty

    Some glass and window makers limit coverage when film is added. We check the manufacturer before we propose a film for insulated units.
  4. Edge clearance

    Film is trimmed just inside the frame. On some door and storefront systems, the gap between glass and frame affects which anchoring method will fit.

Installing security film without closing the business

Schedule a site survey

Security film installs are quiet and need no structural work. For storefronts we usually work before opening or after close so the store keeps trading. On multi-tenant buildings we coordinate with the property manager and schedule suite by suite. Manufacturer care guidance is to hold off cleaning the film for 30 days, and we leave written care instructions for staff and janitorial crews.

We work directly for owners and as a subcontractor to general contractors on tenant improvements. We are an Armorcoat authorized installer, a Madico SafetyShield qualified dealer and a Solar Gard / Saint-Gobain authorized dealer, licensed by the Arizona Registrar of Contractors (ROC #333727).

Cost

Commercial security window film cost factors

Installed security film starts at $9.50 per square foot. Your price depends on:

  • ThicknessHeavier films cost more per square foot.
  • Glass size and countLarge single panes are faster than many small lites.
  • AnchoringAttachment systems are priced per project when specified.
  • Old filmRemoval adds $4.50 per square foot.
  • AccessUpper floor or lift access adds 15%.

Commercial security window film cost per square foot

Installed prices start at $9.50 per square foot. Your written proposal is based on measured glass, film choice and access.

Film gradeInstalled price per sq ft
SecurityFrom $9.50

Prices as of October 2026, from our bid-tool customer rates. Old film removal adds $4.50 per sq ft; upper-floor or lift access adds 15%.

XPEL Security Clear films (4, 8 and 14 mil) carry a 10-year commercial warranty from XPEL, and its exterior films carry 5 years on the film and 2 years on labor, valid when installed by an authorized dealer. Our article on security window film cost goes into more detail, and commercial window security films covers how businesses plan glass protection.

After a break-in

If your glass has already been broken, the order matters. The opening is boarded or secured first, then the glass is replaced by a glazier. Film goes on the new glass once it is set and clean. We can coordinate timing with your glazing contractor so the storefront is protected as soon as the new glass is in, and we can survey the remaining undamaged glass on the same visit so the whole frontage is treated consistently.

Related films

For storefronts that get tagged or scratched, anti-graffiti window film is a replaceable layer over the glass. If you own a house and want the same protection there, see our home security window film page.

We install across the Phoenix metro and Tucson metro, with crews available Valley-wide. Contact us for a site survey and written proposal.

Part of our commercial window tinting services; also available as security window film for homes.

More commercial window tinting films

Service areas

Commercial security window film installation by city

All service areas →

Common questions

Commercial security window film questions

Have a question about your glass? Ask us.

Does window security film really work on commercial glass?

It does what it is designed to do: hold broken glass together so it takes more time and effort to get through, and keep shards from scattering into a store or office. It does not make glass unbreakable. Results depend on film thickness, glass type and whether the film is anchored to the frame.

What is the strongest security window film you install?

The thickest films in our lineup are 14 mil: XPEL Security Clear 14mil, which XPEL publishes at 420 lbs/in break strength on 3 mm glass, and Solar Gard Armorcoat-Clear 14 mil. Thicker is not always the right answer, so we match thickness to the glass and the risk.

How much does security window film cost for a business?

Installed security film starts at $9.50 per square foot. Removal of old film adds $4.50 per square foot, and upper floor or lift access adds 15%. Thickness, glass size and any anchoring system set the final price in your written proposal.

How much does 3M security film cost?

We do not install 3M film, so we cannot quote it. Our security lineup is Solar Gard Armorcoat and XPEL Security Clear, installed from $9.50 per square foot, and we are an Armorcoat authorized installer.

Will security film change how our storefront looks?

Clear security films are close to invisible. XPEL publishes Security Clear 8mil at 89% visible light transmission on 3 mm glass, and Solar Gard publishes Armorcoat-Clear 8 mil at 88% on 6 mm clear glass. Displays and signage stay visible from the sidewalk.

Can security film go on high-traffic glass doors?

Yes. Entry doors and sidelites are among the most common places we install it. We trim film to the glass edge inside the door frame, and the surface can be cleaned with normal non-abrasive glass cleaner after the cure period.

Is security film still worth adding if we have an alarm and cameras?

They do different jobs. An alarm and cameras tell you a break-in happened. Security film is meant to slow the person at the glass, which can buy time before they get inside and limits broken glass across the floor.

Free consultation

Book a free window tinting consultation

Tell us about your glass and we'll send a written proposal.

(480) 977-6994
  • Arizona: ROC Lic# 333727

By submitting, you agree to receive calls and texts about your request from Total Protection Films. Msg & data rates may apply. Reply STOP to opt out. See our privacy policy.

Licensed, factory-authorized window film installers

  • Arizona: ROC Lic# 333727
  • Solar Gard / Saint-Gobain authorized dealer
  • Armorcoat authorized installer
  • XPEL authorized dealer
  • Madico SafetyShield qualified dealer
  • Full XPEL VISION line installed
  • 25 years of window film experience

Because we're factory-authorized, film is installed to manufacturer spec and carries the manufacturer's warranty.