Total Protection Films
Commercial decorative window film: a linear-pattern frosted band on an office glass door and sidelites

Commercial Window Tinting

Commercial Decorative Window Film

Commercial decorative window film gives existing glass an etched, frosted or patterned finish for lobbies, glass partitions, conference rooms and storefronts. It costs far less than replacing glass, can be cut into bands or shapes, and comes off cleanly at lease turnover. We install XPEL and Madico decorative films across Arizona from $8.25 per square foot.

  • From $8.25 per sq ft installed
  • After-hours installs on occupied floors
  • Samples left on the glass for review

Overview

Commercial decorative window film for offices and lobbies

Glass partitions, lobby walls and entry doors are often the first thing a visitor sees, and plain clear glass can make a space feel unfinished. Decorative window film gives that glass the look of etched or sandblasted glass for a fraction of the cost and without taking the glass out of the frame. It goes on in hours, not weeks, and it can be removed when a tenant leaves or the brand changes.

We install decorative film for interior designers, property managers, business owners and general contractors on new build-outs and refreshes. For other commercial film types, see our commercial window tinting page.

Finishes

Etched and frosted glass finishes for commercial spaces

We keep the decorative lineup focused on finishes that look right in professional settings and hold up to commercial cleaning.

  1. XPEL Dusted Crystal

    XPEL Dusted Crystal is a light, etched-glass look. It softens the view rather than blocking it, and XPEL publishes it at 86% visible light transmission on 3 mm glass. It suits lobbies and corridors where you want texture without losing the open feel.

  2. XPEL White Frost

    XPEL White Frost is a denser frosted finish. XPEL publishes it at 65% visible light transmission and 99% UV rejection on 3 mm glass. It is our usual choice for conference room bands and office fronts.

  3. Madico Frost Matte

    Madico Frost Matte is a smooth matte frost. Madico publishes it at 67% visible light transmission and 25% glare reduction on 6 mm clear glass. It reads as a clean, even surface on large glass walls.

Seeing samples on your glass

Each finish has a slightly different tone and texture, so we bring samples to put on your glass under your lighting before you choose. What looks soft and even in a sample book can look brighter or flatter against a lobby lit by daylight, so seeing it in place avoids surprises. On projects with several decision makers, we can leave samples on the glass for a few days so the owner, designer and property manager can each review them.

Where it's used

Decorative privacy window film for offices and storefronts

  • Lobby and reception glass

    Frosted bands or borders give glass walls a finished, branded look.
  • Office fronts and conference rooms

    Decorative bands add a design element and partial privacy at the same time.
  • Glass doors and sidelites

    A band or pattern makes full-height glass easier to see and frames the entry.
  • Storefront transoms and side panels

    Frost can hide stock rooms or ceiling clutter while leaving display glass clear.
  • Restaurants and hospitality

    Frost between dining areas, bars and kitchens divides space without walls.
  • Medical and dental reception

    A softened view between the front desk and treatment areas keeps the space bright and calm.
  • Schools and offices

    Glass corridors and breakout rooms that need a lighter look than solid frost.

Planning

Planning office window film designs

Decorative film is as much about layout as product. A few decisions shape the result:

Coverage. Full-height frost reads as a solid wall. A band at eye level keeps daylight and sightlines above and below. A border around the edge frames the glass without changing it much.

Cut-outs. Frost can be cut so clear lines, shapes or lettering show through. Simple geometric cuts work best on long runs of glass. We draw the layout to scale and get your sign-off before we cut anything.

Consistency. On a floor with many partitions, band heights and margins have to line up from room to room. We set heights from finished floor so the line stays level along the corridor, even where glass sizes change.

Building standards. In multi-tenant buildings, the landlord may have rules on what can be seen from the common corridor or the street. We work with the property manager so the design meets those standards before installation.

Decorative film versus etched or replacement glass

Owners who want a frosted or etched look usually weigh three routes: replacing panes with factory-etched glass, sandblasting or acid-etching in place, or applying film. Replacement glass has the longest lead time and means removing glass from occupied spaces. Etching in place is permanent, which can be a problem in leased space. Film goes on in a single visit, keeps the original glass, and can be taken off or changed later. For tenant improvements, that flexibility is often the deciding factor, because a landlord can return the suite to clear glass for the next tenant.

Working with designers and contractors

On larger jobs, decorative film is often specified by an interior designer or architect and installed under a general contractor. We provide the manufacturer’s published data for each film, physical samples for approval, and a scaled layout showing band heights and any cut-outs. Once the design is signed off, we schedule installation around the other trades, typically after glass is installed and the space has had its final clean. If the design changes during the job, we update the layout drawing before we cut film so every room still matches.

For owners managing more than one site, we keep the approved product and layout on file so later locations or floors can be done to the same standard.

Specs

Commercial decorative window film specs

XPEL

FilmVisible light transmittedTotal solar energy rejectedSHGCUV blockedGlare reduction
Dusted Crystal86%17%0.8335%4%
White Frost65%33%0.6799%28%

Manufacturer-published values measured on 1/8" (3 mm) glass; results on your windows vary by glass type. Sources: spec sheet

Madico

FilmVisible light transmittedTotal solar energy rejectedSHGCUV blockedGlare reduction
Frost Matte67%n/an/an/a25%

Manufacturer-published values measured on 1/4" (6 mm) clear glass; results on your windows vary by glass type. Sources: spec sheet

Installing decorative film on a live site

Schedule a site survey

On new build-outs we coordinate with the general contractor and install once glass is set and cleaned, near the end of the schedule. On occupied floors we work after hours so staff and visitors are not disrupted. Film installation is quiet, needs no structural work, and leaves each area ready to use.

We are a Solar Gard / Saint-Gobain authorized dealer and Armorcoat authorized installer, install the full XPEL VISION line along with Madico and Maxpro films, and hold Arizona ROC license #333727.

Cost

Commercial decorative window film cost

Decorative frost is installed from $8.25 per square foot. The final price depends on:

  • LayoutBands, borders and cut-outs take more labor than plain full coverage.
  • Glass countMany small lites cost more to install than a few large panes.
  • Old film removalAdds $4.50 per square foot.
  • Upper floor or lift accessAdds 15%.

Commercial decorative window film cost per square foot

Installed prices start at $8.25 per square foot. Your written proposal is based on measured glass, film choice and access.

Film gradeInstalled price per sq ft
Privacy frostFrom $8.25

Prices as of October 2026, from our bid-tool customer rates. Old film removal adds $4.50 per sq ft; upper-floor or lift access adds 15%.

You receive a written proposal with the film, layout and square footage before work starts. XPEL decorative films, including White Frost and Dusted Crystal, carry a 5-year commercial warranty from XPEL when an authorized dealer installs them.

Cleaning decorative film in a busy building

Decorative film on partitions and doors gets touched and cleaned more than most glass, so care matters. For the first 30 days after installation, the film should not be cleaned while it finishes curing. A slight haze in that period is moisture under the film and usually clears within a few days, depending on the weather. After that, janitorial staff can use mild dishwashing detergent and water or a commercial glass cleaner, with soft cloths or paper towels only. Tape residue from temporary signs comes off with a soft cloth and mineral spirits or alcohol. We leave written care instructions at closeout so they can go straight to your cleaning contractor.

Decorative film is not a sun control film

Decorative films are chosen for appearance. XPEL publishes Dusted Crystal at 17% total solar energy rejected and 35% UV rejection on 3 mm glass, so it does little for heat or fading. On sun-facing exterior glass, we usually pair decoration on interior glass with a solar window film outside.

Related films

If the main goal is privacy for exam rooms or conference rooms, see privacy window film and frosted window film. For decorative film in a house, our home decorative window film page covers residential options.

We install across the Phoenix metro and Tucson metro, with crews available Valley-wide. Contact us to see samples on your glass.

Part of our commercial window tinting services; also available as decorative window film for homes.

More commercial window tinting films

Service areas

Commercial decorative window film installation by city

All service areas →

Common questions

Commercial decorative window film questions

Have a question about your glass? Ask us.

Can decorative film include our company logo or a custom pattern?

Frosted film can be cut into bands, borders and simple shapes, including a logo, with clear glass showing through the cut areas. We confirm the layout with you on a drawing before cutting, and complex artwork may need a separate graphics step.

Is decorative film a permanent change to the glass?

No. The film bonds to the glass surface but can be removed later with heat and scraping, leaving the glass intact. That makes it a good fit for leased space where the next tenant may want a different look. Removal is priced at $4.50 per square foot.

How do we clean decorative film in a busy lobby?

After the cure period, clean with a soft cloth or squeegee and a non-abrasive glass cleaner. Avoid razor blades and scrubbing pads on the filmed side. We give written care instructions to your janitorial crew.

Does decorative film block heat or UV?

Only a little, and it varies by film. XPEL publishes White Frost at 99% UV rejection on 3 mm glass, but Dusted Crystal at only 35% UV. Neither is a heat film. If solar heat is the issue, a solar film is the better choice.

Can decorative film go on glass doors and sidelites?

Yes. A frosted band or pattern on full-height glass doors makes the glass easier to notice and adds a finished look. We trim the film inside the frame so edges stay clean on doors that open and close all day.

Can you match the same decorative look across several floors or locations?

Yes. Because we use stock manufacturer films, the same product and layout can be repeated on other floors of a building or in other locations in the Phoenix and Tucson metros. We keep your film choice and band dimensions on file.

Free consultation

Book a free window tinting consultation

Tell us about your glass and we'll send a written proposal.

(480) 977-6994
  • Arizona: ROC Lic# 333727

By submitting, you agree to receive calls and texts about your request from Total Protection Films. Msg & data rates may apply. Reply STOP to opt out. See our privacy policy.

Licensed, factory-authorized window film installers

  • Arizona: ROC Lic# 333727
  • Solar Gard / Saint-Gobain authorized dealer
  • Armorcoat authorized installer
  • XPEL authorized dealer
  • Madico SafetyShield qualified dealer
  • Full XPEL VISION line installed
  • 25 years of window film experience

Because we're factory-authorized, film is installed to manufacturer spec and carries the manufacturer's warranty.